REAL LEATHER
FOR WALL AND FLOOR

MADE OF GENUINE, BONDED LEATHER

DEKO LEATHER PUR

Genuine leather panels:
 
Our leather panels are made of genuine, recycled, chrome-free leather, natural latex, natural grease and natural tannins. Laying floors becomes an experience: Precious in design and extremely durable thanks to the environmentally friendly seal. The easy-to-care leather flooring creates a unique ambience.
 

The joint-friendly floor coverings ensure a pleasant, natural walking sensation:

The ideal ground for barefoot walking. Suitable for underfloor heating, this natural genuine leather floor can be combined with pleasant foot warmth even in winter, offering a good alternative to wood, stone or vinyl flooring.

 

Also works glued to the wall:

Bring not only leather on the floor but also leather on the wall with Deko Leather Pur:

Bonded it also serves as a leather wall covering or leather decoration and thus create a noble, high-quality heat-insulating wallart.

 

Easy to clean and for floating or adhesive laying - we offer two versions of our leather floorings:

1. HDF covering: ca. 10.5mm thick (plate size 620x450mm) - only floating lay
2. Tiles covering: ca. 6mm thick (plate size 915x305mm) - only for gluing

 

As adhesive tiles or with HDF plate:

Characteristics:

  • Bonded to the substrate
  • Also suitable for damp rooms and wet rooms

  • Plate size: 915x305mm

Characteristics:

  • Do not get stuck to the substrate
  • With click system
  • Not suitable for damp rooms and wet rooms
  • Plate size: 915x305mm

Technical information


Cleaning and maintenance:

The lifespan of your floor depends on its use, cleaning and maintenance.

We recommend to use a doormat or dirt carpet in the entrance area. The floor is protected by the use of felt glides on table and chair legs.

Use suitable cleaning agents for regular cleaning (eg LOBA Cleaner).

Image
Image
Before Installation:

When gluing the Deko Leather Pur adhesive tiles it is important to bond them to a clean, dry, even and tensile and pressure-resistant and crack-free surface. The laying is suitable for cement screeds, anhydrite / flow coating, hot asphalt / mastic asphalt screed and dry screed installation panels. Substrates and/or subfloors with adhesive residues must be sanded off and cleaned. The substrate must be primed with a suitable precoat concentrate, after drying with a more suitable leveling compound, a layer thickness of min. 2 mm to be compensated. The maximum permissible unevenness of the subfloor must not exceed 2 mm on 1 m length. 

Deko Leather Pur tiles should be acclimatized before installation at a room temperature of 15-25° C and a relative humidity of approx. 40-60%, 24 hours in a closed, surface-mounted package. Please also note that the underground at the time of laying must have a temperature of at least 15° C. Deko Leather Pur tiles can also be installed on underfloor heating, with a maximum surface temperature of 28° C. The adhesive sheets should be checked in daylight for their perfect condition, any transport and material damage must be complained before laying. Differences in color and structure are material-related and therefore no reason for complaint. Adhesive variants are released for installation in damp rooms and wet rooms.

Image

Installation:

For the first row, a landing line is drawn on the ground with the help of a slat or a chalk line. This line should be recorded at a distance of three rows from the wall. Then, only this part of the area about 45 cm (from the line to the wall) with a suitable notched trowel and with a suitable contact adhesive for Deko Leather Pur tiles are painted. Follow the instructions of your adhesive supplier. The plates should be wetted with adhesive over the whole area, they should be pressed strongly. Before the adhesive binds, the plates should be rolled flat with a follower roller (weight 14-25 kg). A bottoming knife or cutter knife can be used to cut the plates. Scrape the plates from above with the knife and break them at the interface.

Before installation:

Deko Leather Pur floors with HDF-Click (high-density wood fiberboard) are laid floating (i.e. not glued to the underground) on a clean, permanently dry, tensile and pressure-resistant as well as level and crackfree surface. The laying is suitable on ceramics and natural stone floors, on PVC, linoleum and plastic coverings, wooden planks and chipboard subfloors as well as all mineral screeds. The substrate must not contain substances which adversely affect the floor or cause interactions. Old floor sand carpets should be removed for hygiene reasons. The maximum permissible unevenness of the subfloor may not exceed 2 mm over a length of 1 m, otherwise it must be compensated with leveling compound. 

The floor should be acclimatized before installation at a room temperature of 15-25° C and a relative humidity of approx. 40-60%, 24 hours in a closed, flat stored in a package. Between your HDF-Click and the subfloor, a PE foil or other vapor barrier must always be laid. HDF-Click can also be installed on hot waterfloorheating, with a maximum surface temperature of 28° C. The boards should be checked in daylight for their perfect condition, any transport and material damage must be complained before laying. Differences in color and structure are material-related and therefore no reason for complaint. Please also check before laying that the tongue and groove are free of swarf or other particles. Deko Leather Pur floors with HDF-Click are not suitable for installation in humid rooms and/or wet cells.

Image

Installation:

Start laying in a corner of the room. An expansion joints of 10 mm against the wall and every other solid construction element. must be maintained. Lay the following panels in direct extension of the first ones. The remaining piece of the first row is used as a panel for the second row. This panel should be at least 30 cm long. To cut the panels, it is recommended to use a hand circular saw, jigsaw or laminate cutter. Place the panel at a slight angle of approx. 10° and click on them by pressing in and gently wagging. On the face side, the panels are clicked in with a tapping block by a lightly beating. Always apply the tapping block (at least 20 cm long) to the tongue, or to the lower groove cheek, not to the „good edge“. Maximum permissible area without additional expansion joints is 15 m x 10 m. HDF-Click is not suitable for full-surface gluing. For pipe connections holes are drilled whose diameter is about 20mm larger than that of the pipe. The covering is done retrospectively with rosettes. Door frames are shortened accordingly, so that the elements below can be laid floating. Skirting and transition strips (insertion rail) are used as conclusion.

Browse our product catalogue:

Echtleder auf Boden Wand

Lederboden und Lederwand aus echtem Leder. Lederprodukte Lederdekoration Ledereinrichtung Designerambiente